How C-41 works
The chemistry in one minute
Developer turns the exposed silver halide into metallic silver. The used-up developer joins with colour couplers in each layer to form cyan, magenta and yellow dyes. This is the only step where time and temperature really matter.
Bleach turns the metallic silver back into silver halide.
Fixer dissolves all the silver halide, leaving only the dye image and the orange mask.
Wash removes the fixer.
Stabilizer contains a wetting agent (and in older formulas formaldehyde) for even drying and dye stability. It is the last bath: no rinse after it.
A blix kit combines bleach and fixer into one bath. It is slower but has one bottle fewer.
Why temperature matters
The standard process runs the developer at 37.8 °C (100 °F) ±0.15 °C. Home kits are more forgiving: ars-imago says a drift of 2–3 °C during development still gives good results as long as the average stays around 38 °C. Colder developer needs more time, and the three colour layers do not slow down by the same amount. So low-temperature processing can shift colour and contrast. This is usually fixable in the scan, but harder to fix in a print.
This timer scales the developer time automatically when you set a different temperature: about 12 % more time per degree colder. That matches the usual figures of 3:15 at 38 °C, about 8:00 at 30 °C and about 13–14 min at 25 °C. The other baths are not critical; anything in the 30–38 °C range works.
Agitation
ars-imago recommends continuous agitation in the developer, for example a roller base or slow continuous inversions.
For hand inversion in a Paterson-type tank, a common routine at 38 °C is: agitate continuously for the first 10–15 s, tap the tank to knock off air bubbles, then do 2 inversions every 30 s. The timer beeps for each cycle. Agitate the same way in bleach and fixer. Stabilizer only needs gentle agitation at the start, so it doesn't foam.
Count the pour-in as part of the step. Start draining about 10 s before the end so the next bath goes in on time.
Pre-heat
The pre-heat fills the tank with 38 °C water so the reels, tank and film reach process temperature. Without it, cold plastic drops the developer by a degree or more right when it matters. Expect the water to come out tinted green, blue or purple. That is the anti-halation layer and is normal.
Reusing chemistry
The ars-imago developer is reusable. Add 15 s for every 4 films already developed: films 1–4 3:15, 5–8 3:30, 9–12 3:45, 13–16 4:00, 17–20 4:15. From the 13th film on, ars-imago also lengthens the fixer from 2:00 to 2:30. The Chemistry tab counts your films and does this automatically.
Push processing
ars-imago: add 30 s per stop pushed. Push C-41 by 1 stop, at most 2. Shadows get thin and colours get harsher. Pulling C-41 is generally not recommended. Overexpose instead, since colour negative handles it well.
Troubleshooting
Dark, dense negatives with milky or grey cast: under-bleached or under-fixed. Re-bleach and re-fix, then wash and stabilize again. This can be done in daylight.
Thin negatives: underexposed, developer exhausted, or developer too cold or too short.
Colour cast that won't correct: developer temperature far off, or developer contaminated with bleach. Always rinse jugs between baths.
Streaks or drying marks: skipped stabilizer, or hard water. Mix the stabilizer with distilled water.
Uneven edges near sprockets: too much agitation. Use gentler, regular inversions.
Where these numbers come from
Confirmed for ars-imago: developer 3:15 at 38 °C, +15 s per 4 films, push +30 s per stop, 38 °C pre-heat, 45 s "extra rapid" bleach at 30–38 °C, fixer 2:00 → 2:30 from the 13th film, stabilizer 1:00, mixing ratios, ±2–3 °C tolerance, 5-week shelf life.
Inferred: the 3:00 pre-heat, 1:30 wash after the bleach and 3:00 wash after the fixer. Check these against the data sheet that came with your kit. Tap Edit times to change any step; your edits are saved.
Standard Kodak C-41 and the blix profile follow the published Kodak process and typical blix-kit sheets (CineStill CS41-style). Always prefer the sheet in your box.